Homemade Tools or Cheap Tricks

Discussion in 'Tool & Shop Talk' started by rthomas771, Mar 1, 2009.

  1. PAINTANK

    PAINTANK Cometosis Obsessivus

    Joined:
    May 27, 2007
    Messages:
    2,842
    Likes Received:
    14
    Trophy Points:
    0
    Location:
    South Central, North Carolina
    Vehicle:
    1973 Comet 2 dr
    When installing the electric Taurus fan I bought, I noticed it was VERY tight and came very close to my engine. Too close in fact for my satisfaction. So I removed the radiator and whacked the radiator mounting tabs with a rubber mallet about a half inch or so flatter, then reinstalled the radiator and fan. Clearance problem solved with room to spare. Quick, simple and effective.
     
  2. baddad457

    baddad457 Member

    Joined:
    Feb 24, 2007
    Messages:
    5,861
    Likes Received:
    141
    Trophy Points:
    171
    Location:
    Opelousas La.
    :thumbs2: Nothing like using a BFH in solving a problem !!! :thumbs2::16suspect It's a great way to relieve stress too !!:biglaugh:
     
  3. facelessnumber

    facelessnumber Drew Pittman

    Joined:
    Oct 4, 2007
    Messages:
    3,710
    Likes Received:
    30
    Trophy Points:
    157
    Location:
    Memphis, TN
    Vehicle:
    '71 Grabber
    Pneumatic siphon pump

    I doubt I'm the first person to do this, maybe I just stumbled on an old trick that everybody else already knew, but I had this idea last night, and it works so nicely, I had to share...

    I was replacing my radiator, and the drain petcock is either not present or completely impossible to see. In the past whenever I've had to drain it for removal or for changing hoses, water pump, etc. I've kept a 4' length of heater hose around to siphon it out. (I should just buy a siphon pump, yes, but I never think about needing one until I'm already in the middle of something.)

    This time I decided, even though antifreeze is quite scrumptious, I didn't want to drink any, so a light went off in my head and I did what you see here in the pictures.

    I poked an air duster into the hose about 2/3 down the length of it. Put the end where the air comes out into an empty jug on the floor, put the other end into the radiator, and hit the button. It creates strong suction. You can hear the liquid coming up the hose, pitch gets higher, and if you let go of the trigger just before the water hits, you won't blast an aerated cloud of glycol in your face, and you will have started a siphon without making a mess, or even having to lay down under the car!
     

    Attached Files:

    Russell likes this.
  4. sierra grabber

    sierra grabber Certifiable

    Joined:
    Sep 29, 2005
    Messages:
    2,808
    Likes Received:
    1
    Trophy Points:
    0
    Location:
    northern nevada
    Vehicle:
    71 grabber red and black; 74 2dr LDO comet
    thats pretty cool! i just use a big shop vac to suck the liquid out of the block (you can almost get it dry) then dump the bucket at the recycle station when i can find one...
     
  5. PaulS

    PaulS Member extrordiare

    Joined:
    May 3, 2004
    Messages:
    4,858
    Likes Received:
    8
    Trophy Points:
    0
    Location:
    Seattle area
    Vehicle:
    1966 Mustang, 1972, 73, 73 and 73 Mavericks
    If you install petcocks in the block that have the little sleeve on them you can put a hose on the petcock and open it. drain it into an old antifreeze jug and you can salvage the used antifreeze if it isn't more than a year old. If it is a year or more old then you can use the jug to recycle it at your local auto parts store.
     
  6. Quinlan

    Quinlan New Member

    Joined:
    Mar 29, 2010
    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    0
    Nice ideas and nice tips for home made tools and cheap home made tools...
     
  7. smiggey

    smiggey Member

    Joined:
    Oct 7, 2009
    Messages:
    22
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Las Vegas
    Vehicle:
    70 Maverick, 89 F-150, 92 K1500
    i know the head bolt turned guide pin trick has been mentioned but get a set for your intake, no slipping gaskets no uneven landings no sliding intakes, just screw in the studs and drop on the intake. and it holds your gaskets in place real nice. i went down to ace and bought 4 of every size bolt in 2 and 4 inch lengths. cut the heads off and now have a full set of guide pins. great for headers too
     
  8. Halbert33

    Halbert33 New Member

    Joined:
    Apr 20, 2010
    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    0
    Hi
    Really interested in your post ...The tips you have given are really appreciable ...i would like to know few more from you ...Thanks for the post ..
     
  9. CornedBeef4.6L

    CornedBeef4.6L no longer here

    Joined:
    Apr 3, 2003
    Messages:
    5,217
    Likes Received:
    6
    Trophy Points:
    137
    Vehicle:
    no longer here
    a 13mm closed end wrench works just as well...
     
  10. Bryant

    Bryant forgot more than learned

    Joined:
    Aug 7, 2007
    Messages:
    6,538
    Likes Received:
    153
    Trophy Points:
    203
    Garage:
    1
    Location:
    San Diego
    Vehicle:
    71 Maverick
    you can make a thread chaser out of a bolt and cut off wheel. if you have some buggered up threads and dont have a tap you can take a bolt that fits the hole and use a cut off wheel to put a couple of cuts accross the first few threads. this will create a cuting edge on the bolt that will clean the threads.
     
  11. fastback86

    fastback86 Loose cars and fast women

    Joined:
    Jun 21, 2008
    Messages:
    401
    Likes Received:
    14
    Trophy Points:
    97
    Location:
    FL
    Vehicle:
    1974 Maverick 351W, 1985 5.0 Mustang coupe, 1996 F150, 2004 Subaru WRX Sti (Don't shoot me, it goes like hell!)
    Good to know!
     
  12. cyclonewill

    cyclonewill Member

    Joined:
    Nov 4, 2005
    Messages:
    703
    Likes Received:
    37
    Trophy Points:
    102
    Location:
    SandSprings, Oklahoma
    Vehicle:
    69.5 Maverick - (2)72 Maverick- 64 comet cyclone- 69 mustang 70 cougar -69 Ranchero - 73 Pinto
    Yep, I'm bringing this thread back.

    As I am installing power regulators today, I was reminded of a handy tool I made for pulling the window rivets. The two sizes are required due to the shape of the access holes, and distance from edge of glass to the rivet.

    Chinese C clamps, a short length of 1/2" tube, and 1/4" rod. Easy, and quick.
     

    Attached Files:

  13. Russell

    Russell Orejano

    Joined:
    Jul 21, 2018
    Messages:
    158
    Likes Received:
    126
    Trophy Points:
    86
    Location:
    New Mexico, 88022
    Vehicle:
    Maverick
    You have a very sick mind......I like it....
     
  14. smegnl

    smegnl Roger Saffle Supporting Member

    Joined:
    Apr 3, 2010
    Messages:
    2,324
    Likes Received:
    336
    Trophy Points:
    197
    Location:
    Wadsworth, Ohio
    Vehicle:
    1970 Grabber Clone
    thanks for bringing this old thread back to life, it was a fun read.
     

Share This Page