EDELBROCK VICTOR jr heads

Discussion in 'Technical' started by valleyracer, Aug 30, 2003.

  1. valleyracer

    valleyracer Member

    Joined:
    Mar 19, 2002
    Messages:
    492
    Likes Received:
    5
    Trophy Points:
    62
    Location:
    Ottawa Canada
    Vehicle:
    1977 Maverick Drag car 399 engine,C4 trans,9"with 4.33 gear ET 10.25 @ 128 mph
    Can anyone tell me what hedder will work with a 302 with Victor jr heads ?:confused:
     
  2. mavman

    mavman Member

    Joined:
    Mar 9, 2002
    Messages:
    2,028
    Likes Received:
    13
    Trophy Points:
    112
    Location:
    Arkansas
    Vehicle:
    '75 Maverick, '03 super duty, '04 Mustang Vee-six!
    Hedman 88300's should work. Even though the ports are raised, I'm told that most off-the-shelf headers will still fit.

    those are some nasty heads for a 302! I like mine....on the windsor. That thing outta scream!
     
  3. valleyracer

    valleyracer Member

    Joined:
    Mar 19, 2002
    Messages:
    492
    Likes Received:
    5
    Trophy Points:
    62
    Location:
    Ottawa Canada
    Vehicle:
    1977 Maverick Drag car 399 engine,C4 trans,9"with 4.33 gear ET 10.25 @ 128 mph
    Those hedman's are too small for the ports; HUGE PORTS, also they are square ports on Victors . I am running Hedman's now.
    The Maverick has a best of 12.06 at 110 mph and these should pull me into the 10's
     
  4. courier11sec

    courier11sec Member

    Joined:
    Apr 19, 2003
    Messages:
    2,589
    Likes Received:
    8
    Trophy Points:
    117
    Location:
    Tucson, AZ
    Vehicle:
    '72 2d to hold my trailer down with.
    Headers

    Try Hooker Super Comps.
    I'd call them direct if it were me.
    Good luck!
     
  5. valleyracer

    valleyracer Member

    Joined:
    Mar 19, 2002
    Messages:
    492
    Likes Received:
    5
    Trophy Points:
    62
    Location:
    Ottawa Canada
    Vehicle:
    1977 Maverick Drag car 399 engine,C4 trans,9"with 4.33 gear ET 10.25 @ 128 mph
    Thanks Ray, I called them yesterday and the guy said they had nothing to fit . I think the guy was the janitor though!!!:mad:
     
  6. courier11sec

    courier11sec Member

    Joined:
    Apr 19, 2003
    Messages:
    2,589
    Likes Received:
    8
    Trophy Points:
    117
    Location:
    Tucson, AZ
    Vehicle:
    '72 2d to hold my trailer down with.
    DIY?

    Well in that case, have you considered a weld up kit?
    Lots of work, but this is the end of the season and you'll have all winter to get them done.
     
  7. valleyracer

    valleyracer Member

    Joined:
    Mar 19, 2002
    Messages:
    492
    Likes Received:
    5
    Trophy Points:
    62
    Location:
    Ottawa Canada
    Vehicle:
    1977 Maverick Drag car 399 engine,C4 trans,9"with 4.33 gear ET 10.25 @ 128 mph
    Maybe if all else fails , hedman elite may fit but will call first ?:(
     
  8. mavman

    mavman Member

    Joined:
    Mar 9, 2002
    Messages:
    2,028
    Likes Received:
    13
    Trophy Points:
    112
    Location:
    Arkansas
    Vehicle:
    '75 Maverick, '03 super duty, '04 Mustang Vee-six!
    You'd probably be better off in the long run to make your own. It's not as hard as people talk it up to be. If you have any experience with tubing it's a breeze.

    might even be cheaper than Hookers or Hedman hustlers or Elites. Would probably work better too. Just my .02 FWIW
    What heads are you running now?
     
  9. valleyracer

    valleyracer Member

    Joined:
    Mar 19, 2002
    Messages:
    492
    Likes Received:
    5
    Trophy Points:
    62
    Location:
    Ottawa Canada
    Vehicle:
    1977 Maverick Drag car 399 engine,C4 trans,9"with 4.33 gear ET 10.25 @ 128 mph
    Right now I am running 1970 351W heads with 194 intake 160 exhaust ported and polished , shaved 30 thousand's for 10.5 compression!
    On a 306 engine . Bought the Victor Jr's with the raised ports, they have huge exhaust ports that match fel-pro #1487 gasket . Anyone know what hedder matches this?
     
    Last edited: Sep 1, 2003
  10. Killercomet

    Killercomet Member MCCI

    Joined:
    Nov 14, 2002
    Messages:
    418
    Likes Received:
    1
    Trophy Points:
    99
    Location:
    Dirtyburg, WV
    Vehicle:
    1973 comet
    Im running Headman 88306 headers i am going to do the same by installing the Vic.Jr. heads i hope they work.
     
  11. slowcomet

    slowcomet Member

    Joined:
    Aug 2, 2003
    Messages:
    102
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    Ca
    Vehicle:
    1975 Comet
    Header

    Hey Killercomet are you sure that is the correct part number for the headers...I couldn't find 88306... could they be 88308? Hedman Elite headers.
     
  12. Killercomet

    Killercomet Member MCCI

    Joined:
    Nov 14, 2002
    Messages:
    418
    Likes Received:
    1
    Trophy Points:
    99
    Location:
    Dirtyburg, WV
    Vehicle:
    1973 comet
    Thats what the summit invoice says there Headman 15/8 coated headers.Unless thats a summit # im not sure.I boght them a year ago.
     

Share This Page