Teach me about Ignitions

Discussion in 'Technical' started by Elephant, Apr 28, 2020.

  1. Elephant

    Elephant Member

    Joined:
    Dec 8, 2013
    Messages:
    130
    Likes Received:
    5
    Trophy Points:
    36
    Location:
    Katy, TX
    Vehicle:
    1977 Maverick
    I haven't had the pleasure of having to deal with ignition systems very much. I know the basics (how distributor works, how points work, etc.). When looking into electronic ignitions (MSD, Mallory, etc.), what does the cam matter when choosing distributor gear type/material? When talking electronic ignition, are all 3 major components (distributor, coil, ignition control module) all replaced together?

    Thanks for the learning opportunity!
     
  2. RMiller

    RMiller My name is Rick

    Joined:
    Dec 12, 2009
    Messages:
    4,124
    Likes Received:
    1,154
    Trophy Points:
    523
    Garage:
    1
    Location:
    Kennewick, WA
    Vehicle:
    1971 Maverick Grabber
    The material the flat tappet cam is made from is different that a roller cam. if your engine is original you will have a flat tappet cam and I believe you need an iron gear but do not take that for fact, I'm not 100% sure on that.
     
  3. Krazy Comet

    Krazy Comet Tom

    Joined:
    Sep 13, 2012
    Messages:
    7,561
    Likes Received:
    2,319
    Trophy Points:
    531
    Garage:
    1
    Location:
    Chesapeake VA
    Vehicle:
    1972 Comet GT clone 306 . 1969 Fairlane Cobra 428CJ 1988 T-Bird awaiting 331 ..
    Yes material of dist gear & cam must match. Flat tappet cams are cast iron, roller steel. A iron dist gear used with steel cam will be worn out in approx 10K mi.

    Generally modules and coils are replaced at same time. Points in orig dist can be replaced with a Pertronix module and one of their coils.. As long as you don't swap cam types, no hassle with gear material.
     
  4. Elephant

    Elephant Member

    Joined:
    Dec 8, 2013
    Messages:
    130
    Likes Received:
    5
    Trophy Points:
    36
    Location:
    Katy, TX
    Vehicle:
    1977 Maverick
    Cool that helps. If I go all in with an MSD system including module and distributor, can I swap distributor gears and use my current one until I change to a roller later?
     
  5. baddad457

    baddad457 Member

    Joined:
    Feb 24, 2007
    Messages:
    5,861
    Likes Received:
    141
    Trophy Points:
    171
    Location:
    Opelousas La.
    You can always change the gear. But as far as MSD goes, they're about the most pricey of ignitions and no better than a stock Ford Duraspark setup.
     
    jasonwthompson likes this.
  6. ike72com

    ike72com Member

    Joined:
    Sep 22, 2019
    Messages:
    408
    Likes Received:
    246
    Trophy Points:
    106
    Garage:
    1
    Location:
    Charleston SC
    Vehicle:
    1972 Comet, 70 mustang, F250 and F100
    You can limp around on bad points. I used to carry cheap spare in glove box. Never a big deal.

    When the electronic goes bad you,re stuck. Could be external coil, coil(thingy) inside distributor or module itself.
     
  7. bmcdaniel

    bmcdaniel Senile Member

    Joined:
    Jul 2, 2002
    Messages:
    6,739
    Likes Received:
    634
    Trophy Points:
    318
    Location:
    York. PA
    Vehicle:
    '70 Maverick Grabber
    LOL I couldn't do that.
    My car doesn't have a glove box...
    So I don't even have a distributor.
     
    Craig Selvey likes this.
  8. ike72com

    ike72com Member

    Joined:
    Sep 22, 2019
    Messages:
    408
    Likes Received:
    246
    Trophy Points:
    106
    Garage:
    1
    Location:
    Charleston SC
    Vehicle:
    1972 Comet, 70 mustang, F250 and F100
    LoL, okay g-box car was my 70stang.
     

Share This Page