Headers compatibility for 302

Discussion in 'Technical' started by Manu, Jan 30, 2018.

  1. Manu

    Manu Member

    Joined:
    Mar 4, 2017
    Messages:
    40
    Likes Received:
    8
    Trophy Points:
    20
    Garage:
    1
    Location:
    France
    Vehicle:
    73 Mustang Grandé, 73 Mustang Mach 1 and soon 73 Maverick...
    Hi,

    I'm looking for headers to install dual exaust on my Maverick. With a 302 and C4 trans, column transmission shift. AC has been removed and power brake is on.
    I read already that Hedmann will fit with no problem but I received an answer from them they told me that they won't fit, with model Hedmann 88300.

    And what about Scott Brake C5ZZ-9430-SS?

    Thanks for answers,

    Manu
     
  2. Hotrock

    Hotrock Rick, an MCCI Member Supporting Member

    Joined:
    Oct 27, 2012
    Messages:
    1,466
    Likes Received:
    713
    Trophy Points:
    313
    Garage:
    1
    Location:
    Munroe Falls, Ohio
    Vehicle:
    1972 Mercury Comet, 1997 Mustang Cobra, 2019 Ford Edge ST
    I run Hooker 6901s with minimal issues. Unfortunately not everyone on this website has had the same luck with installation of those headers. It's my opinion they are still the best longer tube header you can get for out cars.

    If you have power steering you will have to install a PS drop bracket which has its own issues. I for one switched from power to manual steering as I wanted the extra horse power and to avoid the issue of the PS drop bracket continuing to work loose.
     
  3. Manu

    Manu Member

    Joined:
    Mar 4, 2017
    Messages:
    40
    Likes Received:
    8
    Trophy Points:
    20
    Garage:
    1
    Location:
    France
    Vehicle:
    73 Mustang Grandé, 73 Mustang Mach 1 and soon 73 Maverick...
    Thanks. those Hookers looks like a good option. I want to keep power steering.
    But is it ok with column shift gear?

    Found that on Summit site:

    "If you need a set of headers that will fit your Ford Maverick or Mercury Comet 1972 - 1977 vintage these Hooker 6901s are a great choice. The 6901 set I purchased from Summit Racing fit my 1972 Comet with a 302 and AFR 165 heads. No modification to the headers were required. If you have power steering you will need a power steering lowering bracket. Installation is best achieved by raising the vehicle and installing from the bottom. You may have to remove two bolts to disconnect the idler arm from the sub frame. That is it! No jacking up the engine. It doesn't get much easier". Rick from OH.
     
  4. Hotrock

    Hotrock Rick, an MCCI Member Supporting Member

    Joined:
    Oct 27, 2012
    Messages:
    1,466
    Likes Received:
    713
    Trophy Points:
    313
    Garage:
    1
    Location:
    Munroe Falls, Ohio
    Vehicle:
    1972 Mercury Comet, 1997 Mustang Cobra, 2019 Ford Edge ST
    That was my review that I wrote for Summit Racing. I have a floor shift, can't answer your question.
     
  5. Manu

    Manu Member

    Joined:
    Mar 4, 2017
    Messages:
    40
    Likes Received:
    8
    Trophy Points:
    20
    Garage:
    1
    Location:
    France
    Vehicle:
    73 Mustang Grandé, 73 Mustang Mach 1 and soon 73 Maverick...
    Oh really, world is small ;)
    I asked to Summit with my config, wait for answer.
     
  6. 73dragmav

    73dragmav Member

    Joined:
    Oct 19, 2017
    Messages:
    27
    Likes Received:
    5
    Trophy Points:
    26
    Garage:
    1
    Location:
    Everett, WA
    Vehicle:
    1973 Maverick
    I'll double check when I get home but I think I have the same Hooker headers on my '73 302 with column shift and seem to clear just fine. It looks like the previous owner might have modified the shift linkage but I do not know for sure...doesn't look stock though.
     
  7. ray

    ray Member

    Joined:
    Jan 19, 2009
    Messages:
    122
    Likes Received:
    5
    Trophy Points:
    45
    Location:
    portland
    Vehicle:
    71 grabber
    hooker 6901s no exceptions trust me. if you can afford get ceramic coated.
     
  8. Smitty

    Smitty Member

    Joined:
    Feb 10, 2018
    Messages:
    13
    Likes Received:
    1
    Trophy Points:
    6
    Location:
    Keller, Texas
    Vehicle:
    1974 Ford Maverick Grabber
    I had custom suramic long headers mad. Still had issues with my stearing box being in the way.
     
  9. ray

    ray Member

    Joined:
    Jan 19, 2009
    Messages:
    122
    Likes Received:
    5
    Trophy Points:
    45
    Location:
    portland
    Vehicle:
    71 grabber
    You need a drop down bracket. Available online will fix that issue.
     
  10. Smitty

    Smitty Member

    Joined:
    Feb 10, 2018
    Messages:
    13
    Likes Received:
    1
    Trophy Points:
    6
    Location:
    Keller, Texas
    Vehicle:
    1974 Ford Maverick Grabber
    Yeah I meant to say that I also had a bracket made relocate it
     
  11. ray

    ray Member

    Joined:
    Jan 19, 2009
    Messages:
    122
    Likes Received:
    5
    Trophy Points:
    45
    Location:
    portland
    Vehicle:
    71 grabber
    Im in the process of yarding that leaky, wandering P.O.S. off for the manual steering.
     

Share This Page