Question about changing front shocks

Discussion in 'General Maverick/Comet' started by mrcomet, Jan 9, 2016.

  1. mrcomet

    mrcomet Member

    Joined:
    Oct 22, 2007
    Messages:
    212
    Likes Received:
    11
    Trophy Points:
    60
    Location:
    Florida
    Vehicle:
    1971 comet gt
    Hello,

    From researching on this site I basically have the process to change the front shocks (never done this before on my own). I know you have to remove the top bracket. But when I took a better look at it I realized the engine well support bar is over the shock bracket on two of the bolts. Is this supposed to be this way? Do I have to remove the support bar as well or will the shock bracket slide out from underneath the support.

    See attached picture.

    Any help or advice is greatly appreciated!
     

    Attached Files:

  2. dyent

    dyent Member

    Joined:
    Jan 29, 2012
    Messages:
    1,144
    Likes Received:
    432
    Trophy Points:
    258
    Location:
    vancouver bc
    Vehicle:
    1973 Comet 2 dr., 302 w/AR aluminum heads, Toploader 4 spd, 9" Trac-Lok w/3.70
    The shock tower/firewall support brace will have to be removed, if you are lucky enough, once all 3 nuts
    are removed, the support brace might just lift up enough for you to remove the shock bracket. You should
    remove the 2 bolts securing the shock to the bracket, twist the shock 90 degrees. then remove the 3 nuts,
    lift the support brace and finally the shock bracket should just lift off the studs. Good luck!
    David

    if you are unable to lift the support brace, then loosen the bolt/nuts on the firewall where the support brace
    is secured.........
     
  3. 71gold

    71gold Frank Cooper Supporting Member

    Joined:
    Apr 9, 2002
    Messages:
    26,456
    Likes Received:
    2,835
    Trophy Points:
    978
    Garage:
    1
    Location:
    MACON,GA.
    Vehicle:
    '73 Grabber
    the bottom bolts are the tricky ones for me...:bouncy:
     
  4. Craig Selvey

    Craig Selvey Indiana State Rep - MCCI

    Joined:
    Mar 9, 2002
    Messages:
    18,218
    Likes Received:
    1,308
    Trophy Points:
    878
    Location:
    Albany, Indiana
    Vehicle:
    1972 Maverick Grabber - Color: Orange Also, 1976 Ford Maverick 4-door, 1977 Mercury Comet 2-door.
    Easiest to get out with the load of the car still on the suspension.
     
    CA189HJN likes this.
  5. CA189HJN

    CA189HJN Robert Couse-Baker

    Joined:
    Jan 12, 2018
    Messages:
    238
    Likes Received:
    141
    Trophy Points:
    106
    Garage:
    1
    Location:
    Sacramento, California
    Vehicle:
    1973 Ford Maverick 4-door 302
    Thanks. That's the tip I needed.
     
  6. Krazy Comet

    Krazy Comet Tom

    Joined:
    Sep 13, 2012
    Messages:
    7,561
    Likes Received:
    2,319
    Trophy Points:
    531
    Garage:
    1
    Location:
    Chesapeake VA
    Vehicle:
    1972 Comet GT clone 306 . 1969 Fairlane Cobra 428CJ 1988 T-Bird awaiting 331 ..
    Yeah I have a wheel & tire cut in half just for this process. I find hard part is keeping air in tire.
     
  7. Crazy Larry

    Crazy Larry Member

    Joined:
    Jul 16, 2005
    Messages:
    3,557
    Likes Received:
    603
    Trophy Points:
    287
    Location:
    Wichita, Kansas
    Vehicle:
    '73 Maverick 2-door, 302, manual trans
    Changing front shocks on a Maverick is stupid-easy. You don't even have to jack the car up off the ground. Just turn the wheels all the way toward the direction of the side you are working on.
     
    fullcm and Russell like this.
  8. asudevil311

    asudevil311 Member

    Joined:
    Apr 12, 2007
    Messages:
    57
    Likes Received:
    9
    Trophy Points:
    67
    Location:
    Phoenix, AZ
    Vehicle:
    1972 Maverick 302
    This was a great tip. For future person searching this job:

    1. Turn wheels towards the side you plan on replacing.
    2. Remove two bolts from top of shock.
    3. Remove two bolts from bottom of shock - 2 rubber grommets and 1 washer for each post.
    4. Remove the 3 bolts holding the support brace over the shock and loosen/possibly remove the 2 bolts for the support brace that attach above firewall.
    5. Pull shock out of the top of the tower.
    6. Put the new shock in by reversing the steps above.
     
    plynch and fullcm like this.
  9. fullcm

    fullcm Doug

    Joined:
    Jun 10, 2017
    Messages:
    262
    Likes Received:
    39
    Trophy Points:
    61
    Location:
    Michigan
    Vehicle:
    74 maverick
    I need to change out my '74 fronts. I've got a suspension squeak and I'm pretty sure it's the front drivers side shock. I can recreate the noise by just barely pressing down on the bumper. What would happen if I just removed the two bolts that hold the top of the shock to the brace? Basically unloading that shock to see if the noise goes away before buying a new set of shocks.
    Did the support brace change at some time? Mine has an opening at the top (photo) and it looks like the shock may just pull right through it without having to remove the brace (but maybe that bottom flange is too big to fit through). Also, my 1970 Chiltons manual says to remove the hood. I'm not sure why it says that, the shock looks plenty short enough to clear the hood.
     

    Attached Files:

    Last edited: Sep 2, 2023
  10. RMiller

    RMiller My name is Rick

    Joined:
    Dec 12, 2009
    Messages:
    4,125
    Likes Received:
    1,155
    Trophy Points:
    523
    Garage:
    1
    Location:
    Kennewick, WA
    Vehicle:
    1971 Maverick Grabber
    Doubt your squeak is the shocks, these cars are notorious for noisy upper control arms. They need to be grease and that rarely happens. Some don't have zerks and if they do, they are not easily serviced.
     
    mojo, fullcm, dyent and 2 others like this.
  11. TeeEl

    TeeEl Member

    Joined:
    Oct 25, 2019
    Messages:
    730
    Likes Received:
    469
    Trophy Points:
    162
    Location:
    Colorado
    Vehicle:
    '73 Ford Maverick Resto-Mod
    Seriously? "Remove the hood"? What nonsense. Just open the dang thing.
    As previously mentioned, your squeak is not the shocks. You need to grease the upper control arm bushings...
     
    fullcm likes this.
  12. fullcm

    fullcm Doug

    Joined:
    Jun 10, 2017
    Messages:
    262
    Likes Received:
    39
    Trophy Points:
    61
    Location:
    Michigan
    Vehicle:
    74 maverick
    I only suspected the shock because it the squeak came on all of a sudden. I was backing up out of my driveway and had to hit the brakes pretty hard because I saw a car coming at the last minute, of course the front end jumped pretty high and right after that the squeak began somewhere in the front drivers side. I did grease my upper and lower ball joints, they were the only ones that had zerk fittings. I found the grease plugs on my UC arm, no zerks and from what I've read on here it is very difficult to install them without removing the entire arm and I don't want to drill holes in the tower, so I may have to have a shop do that since I do not have a lift or stands.
     
    Last edited: Sep 3, 2023
  13. fullcm

    fullcm Doug

    Joined:
    Jun 10, 2017
    Messages:
    262
    Likes Received:
    39
    Trophy Points:
    61
    Location:
    Michigan
    Vehicle:
    74 maverick
    I only suspected the shock because it the squeak came on all of a sudden. I was backing up out of my driveway and had to hit the brakes pretty hard because I saw a car coming at the last minute, of course the front end jumped pretty high and right after that the squeak began somewhere in the front drivers side. I did grease my upper and lower ball joints, they were the only ones that had zerk fittings. I found the grease plugs on my UC arm, no zerks and from what I've read on here it is very difficult to install them without removing the entire arm and I don't want to drill holes in the tower, so I may have to have a shop do that since I do not have a lift or stands.
    Yes, no way that hood needs removed, maybe it was a typo and they meant RAISE the hood. I wonder how many people over the years actually removed it.
     

    Attached Files:

    Last edited: Sep 3, 2023
    TeeEl likes this.
  14. dyent

    dyent Member

    Joined:
    Jan 29, 2012
    Messages:
    1,144
    Likes Received:
    432
    Trophy Points:
    258
    Location:
    vancouver bc
    Vehicle:
    1973 Comet 2 dr., 302 w/AR aluminum heads, Toploader 4 spd, 9" Trac-Lok w/3.70
    These zerk fittings work great..........
    https://www.holley.com/products/restoration/suspension/front_control_arms/parts/374714-SK
    David
     
    fullcm likes this.
  15. fullcm

    fullcm Doug

    Joined:
    Jun 10, 2017
    Messages:
    262
    Likes Received:
    39
    Trophy Points:
    61
    Location:
    Michigan
    Vehicle:
    74 maverick

Share This Page