Clutch Pedal Removal

Discussion in 'General Maverick/Comet' started by smegnl, Dec 9, 2019.

  1. smegnl

    smegnl Roger Saffle Supporting Member

    Joined:
    Apr 3, 2010
    Messages:
    2,324
    Likes Received:
    336
    Trophy Points:
    197
    Location:
    Wadsworth, Ohio
    Vehicle:
    1970 Grabber Clone
  2. dyent

    dyent Member

    Joined:
    Jan 29, 2012
    Messages:
    1,144
    Likes Received:
    432
    Trophy Points:
    258
    Location:
    vancouver bc
    Vehicle:
    1973 Comet 2 dr., 302 w/AR aluminum heads, Toploader 4 spd, 9" Trac-Lok w/3.70
    Here is picture of Brake and Clutch Pedal assemble, there is a red clip that has to be removed and then Clutch Pedal/shaft can slide out. You have to disconnect the clutch rod and brake rod linkage and carefully remove the blue assist spring, before sliding out the Clutch Pedal/shaft.......
    David
    P1010893.JPG
     
  3. smegnl

    smegnl Roger Saffle Supporting Member

    Joined:
    Apr 3, 2010
    Messages:
    2,324
    Likes Received:
    336
    Trophy Points:
    197
    Location:
    Wadsworth, Ohio
    Vehicle:
    1970 Grabber Clone
    Thanks. This helps. Can I then put the break back in?Or will there not be the mounting gear for the left side of the brake?
     
  4. dyent

    dyent Member

    Joined:
    Jan 29, 2012
    Messages:
    1,144
    Likes Received:
    432
    Trophy Points:
    258
    Location:
    vancouver bc
    Vehicle:
    1973 Comet 2 dr., 302 w/AR aluminum heads, Toploader 4 spd, 9" Trac-Lok w/3.70
    So you just want to remove the Clutch Pedal and then just install the same Brake Pedal? If so, you would have to use a 5/8" bolt/nut to secure the Brake Pedal to the support bracket and use same nylon pedal/shaft bushings (4)........
    David
     
    Last edited: Dec 10, 2019
  5. RMiller

    RMiller My name is Rick

    Joined:
    Dec 12, 2009
    Messages:
    4,124
    Likes Received:
    1,154
    Trophy Points:
    523
    Garage:
    1
    Location:
    Kennewick, WA
    Vehicle:
    1971 Maverick Grabber
    Couldn't he just use the pin from an automatic setup? I'll have to compare mine tomorrow after work.
     
  6. RMiller

    RMiller My name is Rick

    Joined:
    Dec 12, 2009
    Messages:
    4,124
    Likes Received:
    1,154
    Trophy Points:
    523
    Garage:
    1
    Location:
    Kennewick, WA
    Vehicle:
    1971 Maverick Grabber
    After thought....you would do well to swap to the auto setup and sell your manual parts, there's more demand than supply!
     
    Craig Selvey likes this.
  7. smegnl

    smegnl Roger Saffle Supporting Member

    Joined:
    Apr 3, 2010
    Messages:
    2,324
    Likes Received:
    336
    Trophy Points:
    197
    Location:
    Wadsworth, Ohio
    Vehicle:
    1970 Grabber Clone
    Anyone want to trade an Auto set up for a manual set up?
     
  8. smegnl

    smegnl Roger Saffle Supporting Member

    Joined:
    Apr 3, 2010
    Messages:
    2,324
    Likes Received:
    336
    Trophy Points:
    197
    Location:
    Wadsworth, Ohio
    Vehicle:
    1970 Grabber Clone
    I dont have an auto set up.
     
  9. dyent

    dyent Member

    Joined:
    Jan 29, 2012
    Messages:
    1,144
    Likes Received:
    432
    Trophy Points:
    258
    Location:
    vancouver bc
    Vehicle:
    1973 Comet 2 dr., 302 w/AR aluminum heads, Toploader 4 spd, 9" Trac-Lok w/3.70
    Some shafts on the automatic where 3/8" diameter and others where 5/8" diameter, so he would have to make sure to get the correct 5/8" one for his support bracket.....
    David
     
    RMiller likes this.
  10. dyent

    dyent Member

    Joined:
    Jan 29, 2012
    Messages:
    1,144
    Likes Received:
    432
    Trophy Points:
    258
    Location:
    vancouver bc
    Vehicle:
    1973 Comet 2 dr., 302 w/AR aluminum heads, Toploader 4 spd, 9" Trac-Lok w/3.70
  11. smegnl

    smegnl Roger Saffle Supporting Member

    Joined:
    Apr 3, 2010
    Messages:
    2,324
    Likes Received:
    336
    Trophy Points:
    197
    Location:
    Wadsworth, Ohio
    Vehicle:
    1970 Grabber Clone
  12. Craig Selvey

    Craig Selvey Indiana State Rep - MCCI

    Joined:
    Mar 9, 2002
    Messages:
    18,218
    Likes Received:
    1,308
    Trophy Points:
    878
    Location:
    Albany, Indiana
    Vehicle:
    1972 Maverick Grabber - Color: Orange Also, 1976 Ford Maverick 4-door, 1977 Mercury Comet 2-door.

    I would trade you.
     
  13. smegnl

    smegnl Roger Saffle Supporting Member

    Joined:
    Apr 3, 2010
    Messages:
    2,324
    Likes Received:
    336
    Trophy Points:
    197
    Location:
    Wadsworth, Ohio
    Vehicle:
    1970 Grabber Clone
    Let me see what the other guy says since I already reached out to him. Ill give you a yell if not. Id be willing if you paid shipping both ways or such.
     
    Craig Selvey likes this.
  14. smegnl

    smegnl Roger Saffle Supporting Member

    Joined:
    Apr 3, 2010
    Messages:
    2,324
    Likes Received:
    336
    Trophy Points:
    197
    Location:
    Wadsworth, Ohio
    Vehicle:
    1970 Grabber Clone
    Other guy isnt interested. Says he doesnt trust internet strangers, which is fair enough. PM me if your interested still.
     
  15. Craig Selvey

    Craig Selvey Indiana State Rep - MCCI

    Joined:
    Mar 9, 2002
    Messages:
    18,218
    Likes Received:
    1,308
    Trophy Points:
    878
    Location:
    Albany, Indiana
    Vehicle:
    1972 Maverick Grabber - Color: Orange Also, 1976 Ford Maverick 4-door, 1977 Mercury Comet 2-door.
    Would be best to email me (see below). I am not on here enough to catch all my PM's in time.
     

Share This Page