Search Results

Search Again
Page 5 of 6
  1. spork1o1
    Thread

    RPS outer frame rail

    RPS outer frame rail witch is the best one to use for a 73? the one for 70-72 or one for 74-77
    Thread by: spork1o1, Aug 11, 2009, 1 replies, in forum: General Maverick/Comet
  2. spork1o1
    Post

    Parts gone wild

    What are you lookin to get for the hinges?
    Post by: spork1o1, Aug 11, 2009 in forum: General Maverick/Comet
  3. spork1o1
    Post

    V8 z-bar mod (update)

    the thick felt washers are not installed in that pic. I took it for a drive today. The pedal effort is that of a hydraulic setup, but still has...
    Post by: spork1o1, Aug 3, 2009 in forum: General Maverick/Comet
  4. spork1o1
    Thread

    V8 z-bar mod (update)

    I have every thing ready to mock up on the car. I need to install 2 grease fittings in the z-bar. Here is a teaser pic of the engine side with...
    Thread by: spork1o1, Aug 2, 2009, 2 replies, in forum: General Maverick/Comet
  5. spork1o1
    Post

    toploader i.d.

    I bet the casting # on your tail shaft is C4ZR-7A040-A from 1964-73 Mustang, Cougar 289, 302, 351 engines...
    Post by: spork1o1, Jul 29, 2009 in forum: Technical
  6. spork1o1
    Post

    not starting.. new engine

    you were able to turn the flywheel to install the converter nuts correct? then you installed the starter and it would not rotate after correct?...
    Post by: spork1o1, Jul 29, 2009 in forum: Technical
  7. spork1o1
    Post

    not starting.. new engine

    How much gas did you pour in the carb to start it. if you pour in to much you can hydro lock the engine. if the starter and flywheel check out...
    Post by: spork1o1, Jul 29, 2009 in forum: Technical
  8. spork1o1
    Post

    Number 32.....

    yep they look like the mustang mounts I used on my first maverick.
    Post by: spork1o1, Jul 27, 2009 in forum: General Maverick/Comet
  9. spork1o1
    Post

    installed trac-loc, vibration?

    is the yoke on the center section you removed the same length as the one on the center section with the trac-loc?
    Post by: spork1o1, Jul 26, 2009 in forum: Technical
  10. spork1o1
    Post

    Installing Bucket Seats Advice Needed

    I have a set of the correct maverick seat tracks on ebay right now and I live an hour north of grand rapids so you could save on shipping.
    Post by: spork1o1, Jul 22, 2009 in forum: Technical
  11. spork1o1
    Post

    toploader i.d.

    can you post a pic of both sides of the trans?
    Post by: spork1o1, Jul 20, 2009 in forum: Technical
  12. spork1o1
    Post

    Found posible 8" posi w/ 3.55's... $175 to much?

    It came out of a 67 Cougar and yes I just put it in and it works great.
    Post by: spork1o1, Jul 18, 2009 in forum: General Maverick/Comet
  13. spork1o1
    Post

    Found posible 8" posi w/ 3.55's... $175 to much?

    I gave $125 plus drove 6 hours round trip to get a 8" limited slip center section, sight unseen
    Post by: spork1o1, Jul 18, 2009 in forum: General Maverick/Comet
  14. spork1o1
    Post

    Found posible 8" posi w/ 3.55's... $175 to much?

    can you get under it to look at the tag? posi w/ 3.55's should be (3L 55) on the tag
    Post by: spork1o1, Jul 18, 2009 in forum: General Maverick/Comet
  15. spork1o1
    Post

    V8 z-bar mod

    My z-bar is out for repair, found a crack in the lower arm. Hope to get it back Monday. While the guy is repairing it he is going to give me a...
    Post by: spork1o1, Jul 18, 2009 in forum: General Maverick/Comet
  16. spork1o1
    Post

    Timing chain cover problem!!

    how do you get 312 cubes out of a 302. .030 is only a 306 is it not?
    Post by: spork1o1, Jul 17, 2009 in forum: Technical
  17. spork1o1
    Post

    Timing chain cover problem!!

    can you post a pic?
    Post by: spork1o1, Jul 16, 2009 in forum: Technical
  18. spork1o1
    Post

    aluminum vaccum lines on firewall?

    I think you are talking about the actual brake lines. and the vent line for the gas tank. the bigger one is the vent, and the small one goes to...
    Post by: spork1o1, Jul 16, 2009 in forum: Technical
  19. spork1o1
    Post

    Brazilian Parts - what is available in Brazil

    I am having the same problem with ica997 from ebay.
    Post by: spork1o1, Jul 16, 2009 in forum: Foreign Mavericks
  20. spork1o1
    Post

    170ci 3spd to 5.0 3spd - What's needed?

    The gear ratios in the 200 i6 trans you have will not bee fun behind a V8. You need a top loader bell housing with sbf bolt patern. For a 91 5.0...
    Post by: spork1o1, Jul 13, 2009 in forum: Transmissions
Showing results 81 to 100 of 106 Next >
Search Again
Page 5 of 6