72 Mercury Comet GT in Germany

Discussion in 'Maverick/Comet Projects' started by tody, May 9, 2009.

  1. tody

    tody Member

    Joined:
    Apr 12, 2008
    Messages:
    1,828
    Likes Received:
    212
    Trophy Points:
    178
    Garage:
    1
    Location:
    cologne, germany
    Vehicle:
    72 comet gt, 67 club wagon, 65 mustang
    One thing off the list - it wasn't the rear caliper leaking, it was the axle shaft seal. Replaced that, everything should be good.
    Got the engine running with open headers. No obvious leaks on the power steering and the supposedly rebuilt pump does not make any funny noises, for now I call this a win.
    Cooling system has the heater core bypassed. It was leaking through the threads of the temp switch in the thermostat housing. I had not put in antifreeze yet, so it was easy to drain the system and seal the switch up with teflon tape.

    Still, brakes and clutch need to be bled.
     
  2. mav1970

    mav1970 Bob Hatcher

    Joined:
    Mar 9, 2002
    Messages:
    10,633
    Likes Received:
    322
    Trophy Points:
    398
    Location:
    Mountain Top Pa
    Vehicle:
    69.5 Maverick 393 Cleveland Stroker
    Like looking at your modification photos, Thomas - it must be a horror that everything is so tight :)
     
  3. tody

    tody Member

    Joined:
    Apr 12, 2008
    Messages:
    1,828
    Likes Received:
    212
    Trophy Points:
    178
    Garage:
    1
    Location:
    cologne, germany
    Vehicle:
    72 comet gt, 67 club wagon, 65 mustang
    Well, everything tight but still with clearance is a LOT better than the old headers hitting almost everywhere :D
    So in the end, the car should be a lot better than before!
     
  4. tody

    tody Member

    Joined:
    Apr 12, 2008
    Messages:
    1,828
    Likes Received:
    212
    Trophy Points:
    178
    Garage:
    1
    Location:
    cologne, germany
    Vehicle:
    72 comet gt, 67 club wagon, 65 mustang
    Brakes are fully bled.
    Clutch not so much, there is still air trapped in the system. Will try again this weekend!
     
  5. tody

    tody Member

    Joined:
    Apr 12, 2008
    Messages:
    1,828
    Likes Received:
    212
    Trophy Points:
    178
    Garage:
    1
    Location:
    cologne, germany
    Vehicle:
    72 comet gt, 67 club wagon, 65 mustang
    Brakes had a leak at the distribution block. Turned out that the copper washer from the rebuild kit was ever so slightly too large in diameter so the front port would not seal. Replaced it with the old washer, now it's leak free.

    Clutch is fully bled, too. Has a nice throw at the slave cylinder, and the clutch is fully disengaging.

    Still too loud with just the headers on ;) Will go to an exhaust shop to fab two new intermediate pipes on monday!
     
  6. tody

    tody Member

    Joined:
    Apr 12, 2008
    Messages:
    1,828
    Likes Received:
    212
    Trophy Points:
    178
    Garage:
    1
    Location:
    cologne, germany
    Vehicle:
    72 comet gt, 67 club wagon, 65 mustang
    it's alive, sort of.

    • bought a new p/s pump. the rebuilt one on there did not put out enough pressure in idle. borgeson works good with the new pump.
    • while the heater box was out, i noticed an ever so slight leak on the heater core. had that fixed, heater box is back on.
    • replaced the fan switch with a 195/210 unit, instead of the 185/200 which was on there. the 5° degree difference was not enough to switch the fan off, with the new one this actually works.
    brakes will need to be bled again. pedal is a little too soft, with the DOT5 i use it sometimes can be a pain to get all the air out.
    will give the car a good wash next weekend, and then it should be back on the road for a shakedown test of all the new things i put in!
     
    Krazy Comet likes this.
  7. tody

    tody Member

    Joined:
    Apr 12, 2008
    Messages:
    1,828
    Likes Received:
    212
    Trophy Points:
    178
    Garage:
    1
    Location:
    cologne, germany
    Vehicle:
    72 comet gt, 67 club wagon, 65 mustang
    It's back on the road. Drives like a whole new car, the Borgeson upgrade was well worth it.
    There's a couple of things that need to be dialed in - need to recheck the alignment, pulls slightly to the left.
    Also, the bracket for the clutch slave cylinder flexes a little, probably will make a new one out of thicker material.
    Will need to find a way to adjust free travel at the clutch pedal.

    I hope I get to drive it more this summer. Pretty rainy here in Germany, for weeks now.
     
    Stefan and mojo like this.
  8. mojo

    mojo "Everett"- Senior Citizen Supporting Member

    Joined:
    Jul 20, 2009
    Messages:
    5,250
    Likes Received:
    818
    Trophy Points:
    498
    Garage:
    1
    Location:
    Chicago
    Vehicle:
    73 Comet GT-302 4bl
    What pump do you have? My car is out of service cuz pump leaking at pressure fitting, second Borg pump in 9 years. I have always had seepage at steering box pressure fitting. I'm taking pump and hose to local rebuilder this week, see if they can resolve resivior leak b4 I resort to buying another pump.
    I'm interested in knowing your alignment spec's, once you get it all sorted out.
     
  9. dyent

    dyent Member

    Joined:
    Jan 29, 2012
    Messages:
    1,144
    Likes Received:
    432
    Trophy Points:
    258
    Location:
    vancouver bc
    Vehicle:
    1973 Comet 2 dr., 302 w/AR aluminum heads, Toploader 4 spd, 9" Trac-Lok w/3.70
  10. tody

    tody Member

    Joined:
    Apr 12, 2008
    Messages:
    1,828
    Likes Received:
    212
    Trophy Points:
    178
    Garage:
    1
    Location:
    cologne, germany
    Vehicle:
    72 comet gt, 67 club wagon, 65 mustang
    @mojo : I'm using a new Lares 12101 Ford pump, off rockauto.
    I didn't want to use the GM saginaw pump, and there are issues with used and rebuilt ford units not putting out enough pressure.
    But with the new pump, I'm getting decent results. When idling at 750rpm, the power assist is a little low, but everything above is really good.

    alignment specs are above in this thread somewhere.
    roughly like @dyent stated - basically as much caster as possible.
    somewhere around 3°, and I already had to put in shims on the driver side to get that much.
     
  11. mojo

    mojo "Everett"- Senior Citizen Supporting Member

    Joined:
    Jul 20, 2009
    Messages:
    5,250
    Likes Received:
    818
    Trophy Points:
    498
    Garage:
    1
    Location:
    Chicago
    Vehicle:
    73 Comet GT-302 4bl
    Thanks for reply, Tody! I also have low assist a low idle but my issue w/ Saginaw was to much sensitivity above 55mph and still a little sensitive at 70 on windy days, otherwise it works well.

    Have you driven at highway speeds, if so, how was the experience.
     
  12. tody

    tody Member

    Joined:
    Apr 12, 2008
    Messages:
    1,828
    Likes Received:
    212
    Trophy Points:
    178
    Garage:
    1
    Location:
    cologne, germany
    Vehicle:
    72 comet gt, 67 club wagon, 65 mustang
    Sure, took it to the Autobahn today. 160 km/h which translates to 100 mph with no issues.
    I know the car is good for over 140 mph, but the traffic was too dense today.
    But I will surely need to accommodate myself to the new steering before I try that out!
     
    Stefan likes this.

Share This Page